my phone is w610i! when i try to f;lash my phone using "bypass db2020 security" to apply "quick access patch", i get the following log........

CID52 BYPASS PROCEDURE STARTED
Processing part1...
CSloader version:
070410 1557 HANCXC1250562_DB2020_CSLOADER_R3A009
Processing part2...
Processing part3....
BOOTROM MODE DETECTED
OTP LOCKED:1 CID:51 PAF:1 IMEI:354********* CERT:N/A
FLASH CID:52 COLOR:RED
LDR:061201 1314 HANCXC1329129_DB2020_FLASHLOADER_R2A005
Flash ID check:2019
Flash props sent ok

REMOVE CABLE FROM PHONE
REMOVE BATTERY FROM PHONE, THEN INSERT IT BACK
THEN PRESS "READY"

HOLD "C" BUTTON AND ATTACH PHONE

CID52 BYPASS PROCEDURE FINISHED

ChipID:9900,EMP protocol:0301
PHONE IS RED RETAIL PRODUCT
FLASH CID detected:52
Speed:921600
Trying to launch embedded bootloader...
embedded flashloader not responds !
Elapsed:360 secs.


NOW some ppl may answer that its due to "bad cable" as I read some where before as well, but when I "only try to flash" my main, i get no error......!!!! then what can be the problem???? i can`t apply .vkp patches

make sure you have a fully charged battery and latest usb flash drivers installed when using the db2020 bypass method.

thanx 4 a quick reply..........
I`ll try it out after some time when my phone`s battry`s full.

[oops! I forgot to "censor" my IMEI number ]

wellll........... the problem really seems to be a WEIRD one!! I charged my phone battry to 100% and got the same result just to check what XS++ and jdflasher say about it, I connected my phone with both the applications and got these results............ (XS++ stuck at the point, where I have taken the screenshot and Jdflasher gave an error)
PLEEEEAAAASE recommend me a good solution to this problem........

somebody please help me. I really m in trouble

theres something wrong with your usb flash drivers, open the setool lite folder drivers then usb flash drivers then right click on ggsemc.inf and then click install.

first, thanks for the reply
secondly, I dont think so that its due to the drivers because I am NOT having any kind of problems in accessing my FS through FAR (SEFP plugin)
???????????

The problem is that you dont let Setool2lite load the quick access patch to the main properly..

You should wait a few seconds and this could happen..

Going to execute VKP script....
Starting to process VKP patch script: C:\Documents and Settings\..\..\..\quick_access_W610_R6BC002.vkp
VKP script loaded OK. Lines: 1637

In this point, the program seems to stop for a minute without activity (but is still working..)

Patch structure created OK. Determining blocks to read...
New block #0000 added: $44140000
New block #0001 added: $45A80000
Blocks selected OK. Reading blocks: 2
Blocks readed to memory OK. Checking contents...
Blocks patched OK. Start writing...
Block 0 written
Block 1 written
VKP script executed OK
Elapsed:1076 secs.

Then, when you load any .vkp with the option "use quick access patch", you shouldn t have any problem.


(sorry for mi english, I m from Argentina ). Regards

thnx for the reply bro. Bt I DID wait for many time till setool2lite ITSELF disconnected my phone saying "embedded flashloader not responds" (that`s what the topic has been named after)

hmmm
maybe your cable is with conection problems?

get an eraser and clean the cable pins, than clean the fastport connector on your phone, also try connecting the cable to a diff USB port, try one from the back of your PC.

any luck?

Damn! still no luck. I even tried a different DCU60 cable............ but everything`s same

ey we have the same problem, i have my k810i upgraded from k800i.. im flasing my k810 to the latest firmware, then apply a new patch.. but after i flash, i tried to use the use quick access patch then load a .vkp file, then click "Write Script" . but we have the same problem.. Embedded FlashLoader Not Responds. My phone turns ON. instead of start writing the .vkp Patch.. it was succesful when i place a Main file in the add button and together with the .vkp patch in the Misc. and Clicked Patch. it was successful, i have new patch.. but only one patch.. i cant patch two patches.. thank you , i hope somebody can help us.

try seus but seus flash your phone back to k550

I have the same problem, can't succeed to write the script of vkp patch, always the phone turns on and directory is opened, any solution for this problem???

number1 is correct!

for w610i "embedded flashloader not responds !" problem, you must do this what number1 says.

it works for me.